Classic America

HomeBlog

Installation

How Much Does It Cost to Install a Mini Split?

Classic AmericaNov 16th 20264 min read

Published US ranges. Single zone.
Diagram for this guide: Published US ranges.

The short answer

  • How much does it cost to install a mini split? For one indoor head, commonly published US ranges are about $2,500–$6,500 all-in on a straightforward job, and about $4,000–$8,500 when the wall or the circuit is trickier.
  • Labor and site materials on an easy job are often published at around $1,000–$2,500. A new dedicated circuit, when your panel has space, often runs from a few hundred dollars to about $1,500.
  • A two-head job is often published at around $5,500–$12,000+. Those are industry ranges, not a Classic America quote.

The numbers

Commonly published US ranges, labeled so they don't get counted twice
JobPublished rangeWhat it usually means
Straightforward single zone$2,500–$6,500All-in. Often includes some equipment.
Harder single zone$4,000–$8,500Longer lines, masonry, or a new circuit.
Labor and site materials$1,000–$2,500The work, on an easy job.
New dedicated circuitHundreds–$1,500Panel has room. A panel replacement is more.
Two indoor heads$5,500–$12,000+Two line sets and more labor.
Chart of commonly published US mini split install ranges, from an easy single zone through a dual-zone job.
Published ranges, not a Classic America bid. Ask your contractor whether the equipment is already included in the number.

The question is almost never the sticker

“How much does it cost to install a mini split?” sounds like it has one answer, but it's really two bills that tend to get lumped together: the equipment, and the labor to put it on your wall. Cost guides also mix all-in totals (equipment plus labor) with labor-only totals. If you've already bought the system, you want a labor bid. If the contractor is supplying the equipment, you'll want to know which model is included in the all-in number.

Classic America doesn't sell installation or publish a local labor rate. The ranges above are the ones other US cost guides repeat, and your bid may land outside them. Our line-by-line look at the quote shows what should be in writing before you compare two contractors.

What moves the number

  • One head versus two. DUET is one outdoor unit with two indoor heads, so the labor isn't just a copy of a single-zone install.
  • 115V versus 208/230V. Our 9,000 and 12,000 BTU systems are 115V. The 24,000 BTU system is 208/230V and rated 17 SEER2, and DUET is 208/230V too. A new circuit means electrical labor.
  • Line length beyond the precharge. Single-zone spec sheets are precharged for 25 ft. The maximum is 50 ft on the 9,000 and 19 SEER2 12,000, 49 ft on the 17 SEER2 12,000, and 65 ft on the 24,000 BTU model. DUET is precharged for 25 ft per line, with a maximum of 131 ft, and the kit includes 2 x 16 ft. Extra refrigerant is a job for a licensed tech, not a hardware-store can.
  • Where the outdoor unit sits: a ground pad, a wall bracket, or a roof. Our BRA-2002 bracket is listed at $26.99, and that's just the hardware.
  • Permits and condo or HOA approval. Those vary locally and aren't included in the equipment price.

From the spec sheet

  • 12,000 BTU/h cooling · 1 ton
  • 19 SEER2
  • 115V
  • Up to 550 sq ft
  • Heating nameplate 12,200 BTU/h
View model

From the spec sheet

  • 23,000 BTU/h cooling · 1.92 tons
  • 17 SEER2
  • 208/230V
  • Up to 1,400 sq ft
  • Heating nameplate 22,400 BTU/h
View model

Please don't add these ranges to the list price

  • A published all-in range often already includes equipment, so adding it on top of a $735 system counts the machine twice.
  • A labor-only bid should state in writing that you're supplying the equipment.
  • The lowest bid that skips the vacuum, a proper flare, or a licensed electrical permit isn't really the cheap install. It's the one that can void your 5-year compressor / 1-year parts warranty.
  • Planning a DIY mount is fine. Refrigerant connections and the circuit are jobs for licensed pros.

Write the run and the voltage down before you ask for a bid. The Install Planner checks both against the model.

Get a number that belongs to your wall

Before you call anyone, use the Install Planner to pin down line length, voltage, and mounting. Then ask two licensed contractors to quote the same scope. For help with placement, see what to plan before install day. And if you haven't settled on a BTU size yet, start with the Size Finder, because the wrong size wastes money on both bills.

FAQ

Common questions

How much does it cost to install a mini split?

Commonly published US ranges are about $2,500–$6,500 all-in for a straightforward single zone, and about $5,500–$12,000 or more for two heads. Those aren't Classic America prices.

Does that include the mini split itself?

Sometimes, so it's worth asking. Our equipment is listed at $695, $735, $769.50, $1,450, or $2,065 for DUET. Please don't add an all-in range on top of a unit you've already bought.

Why do two quotes differ by thousands?

A new 230V circuit, a long line set, a condensate pump, masonry, or a second head all change the labor. Compare the line items, not just the total.

Can I install it myself and skip the labor?

You can plan and mount it. A licensed HVAC technician should make the refrigerant connections, and a licensed electrician should handle the circuit. You're covered for 5 years on the compressor and 1 year on parts, and a non-professional install can put that at risk.

Supporting diagram for Published US ranges.
The chart already drawn for this topic.
Refrigerant, vacuum, and dedicated electrical work belong with a licensed HVAC pro. Homeowner planning stops at mounting and the line set.

Check the article

Fill in the number from this article

  1. For one indoor head, commonly published US ranges are about $____–$6,500 all-in on a straightforward job, and about $4,000–$8,500 when the wall or the circuit is trickier.

  2. Labor and site materials on an easy job are often published at around $____–$2,500.

  3. A new dedicated circuit, when your panel has space, often runs from a few hundred dollars to about $____.

  4. A two-head job is often published at around $____–$12,000+.

Next stepInstall PlannerLine set, power and mounting checked against your model before install day.Open the tool